※ Completely wireless system with a signal field of closed loop circuit.
※ Rechargeable & Waterproof Receiver gives your dog more freedom.
※ 20-150 meters controlling range between transmitter and collar receiver.
※ 100 level adjustable correction levels for effective dog fencing.
※ Receiver delivers corrections only when it loses signals from the transmitter.
※ Capable of multi-dog fencing at the same time.
Wireless Pet Fence With Rechargeable And Waterproof Receiver | KD661
WIRELESS DOG FENCING SYSTEM
The wireless Fence is the safest, simplest form of pet containment ever. The instant fence operates using the same principles as an under ground fence, yet is completely wireless. This wireless fence sets up in an instant and is completely portable, so it’s great for travel or when you move into a new home.
CONSTANT SIGNAL CONTROLLING DESIGN
The Wireless Fence uses a constant radio signal to create a “stay zone”. The receiver collar worn on your dog picks up the signal. If your dog ventures out of the “safe zone”, which is very rare once he is properly trained, he will hear a warning tone followed by a light static correction which startles your dog but is completely safe and humane.
SIMPLE & QUICK DOG FENCING SYSTEM
With a little training that is simple and quick. Your pet learns his boundaries and will stay safe at home. Setting up the boundary of your yard takes only a few minutes by adjusting the rang on the transmitter which from a radius of just a few meters to up to 150 meters.
Wireless Fence Introduction:
The Wireless Fence Pet Training System comes with a portable Wireless Fence Unit that establishes an invisible boundary by transmitting radio signals to the Pet Collar Unit up to a distance of 150 feet line of sight from the transmitter. When your dog reaches the boundary zone (about 2 to 3 feet before the real boundary), the Pet Collar Unit that is worn on your dog emits a warning beep followed by a static correction to get its attention until it backs away from the boundary zone.
The Pet Collar Unit is equipped with a safety feature such that it will stop delivering static correction if your dog stays outside the boundary for more than 30 seconds. The boundary zone can be marked with Boundary Flags as a visual aid for your dog, especially during the training stage.
How do buttons work:
Power Indicator LED-Display the working status of the system, it normally works normally. Blinking is the line off. Need to be repaired.
Display Levels of Transmitter Signal-Showing the sensitivity of the dog collar, the system has a hundred sensitivity level, showing the greater the number, the higher the level of sensitivity, the smaller the scope of the dog’s activities.
ON / OFF Button-System switch button, long press this button to start the system, Power indicator light is always on.
Increase / Decrease Transmitter Signal Level-Sensitivity adjustment button, min adjust the small sensitivity, max adjustable sensitivity. Different dogs with different sensitivity effects will be better.
To turn the Transmitter on
Turn on the transmitter, and it would emit a 433Hz radio signal around your house. Your pet wears a lightweight receiver collar which keeps connecting with signals from the transmitter. Your dog could enjoy his time freely in the signal covered area, and when he tries to walk close to the edge of the signal covered area, the receiver would deliver a series of corrections to keep him inside of the area.
To turn the Receiver Collar on
1. Pre-correction warning tone: when the dog reaches the edge of the signal field it will hear a warning tone that lasts about two seconds. If the dog does not return to the safe area, it will receive a continuous correction by warning tone & static shock until it returns to the area.
2. Run-through prevention: the receiver automatically increases the correction as the dog approach to the signal edge. The dog cannot “run through” the signal field without receiving a strong correction
Connect transmitter and receiver:
Set up collar receiver
Before first using our Rechargeable and Waterproof Collar Receiver please make sure charging it at least 4 hours. Turn on the power button on the receiver and the red LED light will turn on. When the indicator light turns flashing red it means the battery is running down and needs to be recharged.
Receiver auto sleep mode:
The receiver goes into sleep mode when the vibration sensor inside stays in still over 2-3 minutes, it could save much of the power comparing the system without the similar design, and it could be activated by shaking or vibration. When you find the collar beeps with red led light flashing, you need to charge it before usage.